• Xưởng sửa chữa máy địa vật lý

    Xưởng có nhiệm vụ chính là bảo dưỡng, sửa chữa và hiệu chỉnh các máy móc thiết bị điện tử phục vụ cho các đơn vị trong Xí nghiệp địa vật lý giếng khoan. Ngoài ra xưởng còn nghiên cứu đưa vào ứng dụng và phát triển công nghệ tin học trong công tác địa vật lý

  • Trung tâm Phân tích và Xử lý số liệu

    Có nhiệm vụ đánh giá chất lượng tài liệu do Xí nghiệp Địa vật lý thực hiện.

  • Đội công nghệ cao

    Khảo sát địa vật lý tổng hợp trong giếng đang khoan. Đo địa vật lý tổng hợp, bắn mìn.

  • Đội Kiểm tra công nghệ khai thác

    Có nhiệm vụ là đo khảo sát và kiểm tra công nghệ khai thác trong các giếng khai thác và bơm ép.

  • Đội Carota khí

    Đội Carôta khí có nhiệm vụ chính là khảo sát carota khí, cung cấp kịp thời các số liệu để xác minh trữ lượng, tình trạng các giếng khoan.

  • Đội thử vỉa

    Đội có nhiệm vụ thử vỉa ở các giếng khoan nhằm định hướng cho công tác khoan, xác định tình trạng và đo vỉa, cung cấp thông tin để xác định trữ lượng công nghiệp của giếng

L&TD

LOGGING & TESTING DIVISION

RTTS Safety Joint

RTTS Safety Joint

The RTTS safety joint is an optional emergency backoff device. The safety joint releases the workstring and tools above the packer if the packer becomes stuck during operations.The design of the RTTS safety joint makes unintentional operation difficult.

Features and Benefits

•  Positive sequence of operation helps prevent premature release.

•  Tools above it can be retrieved when string is stuck

Operation

The RTTS safety joint is run immediately above the RTTS packer so that the greatest number of tools above the packer can be removed.Before the safety joint can be used, a tension sleeve located on the bottom of the lug mandrel must first be parted by pulling up on the workstring.After the tension sleeve has parted, the safety joint is released by right-hand torque while the workstring is rotated a specified number of cycles.

 


RTTS Safety Joint

Casing Size (in) OD  in. (cm) ID   in. (cm) Thread connnections Length in.  (cm) Tensile Rating** lb (kg)     Burst Rating** psi (kPa)   Collapse Rating** psi (kPa)
7 to 7 5/8 5.00   (12.70)   2.44 (6.20)   2 7/8 EUE 39.9    (101.4)  

164,000  (74 390)  

   12,000        (82 738)  

  10,900        (75 153)

8 5/8 to 13 3/8 6.12   (15.54)   3.12 (7.92)   4 1/2 IF 42.7      (108.5)   301,000  (136 533)      13,700  (94 459)  

 10,400       (71 706)

These are the most common sizes. Other sizes may be available.

**The values of tensile, burst, and collapse strength are calculated with new tool conditions, Lame’s formula for burst and collapse strength, and stress

area calculations for tensile strength.

These ratings are guidelines only. For more information, consult your local Halliburton representative.

RTTS Packer

The RTTS packer is a full-opening, hookwall packer used for testing, treating, and squeeze cementing operations. In most cases, the tool runs with a circulating valve assembly.The packer body includes a J-slot mechanism, mech anical slips, packer elements, and hydraulic slips. Large, heavy-duty slips in the hydraulic holddown mechanism help prevent the tool from being pumped up the hole. Drag springs operate the J-slot mechanism on ≤ 3 1/2-in. (88.9-mm) packer bodies, while larger packer sizes ≥ 4-in. (101.6 mm) use drag blocks. Automatic J-slot sleeves are standard equipment on all packer bodies. 

The circulating valve, if used, is a locked-open/locked-closed type that serves as both a circulating valve and bypass. The valve automatically locks in the closed position when the packer sets. During testing or squeezing operations, the lock prevents the valve from being pumped open. A straight J-slot in the locked-open position matches with a straightJ-slot (optional) in the packer body. This combination eliminates the need to turn the tubing to close the circulating valve or reset the packer after the tubing has been displaced with cement.

Features and Benefits

•   The full-opening design of the packer mandrel bore allows 

large volumes of fluid to pump through the tool. Tubing-type guns and other wireline tools can be run through the packer.

•  The packer can be set and relocated as many times as necessary with simple tubing manipulation.

•   Tungsten carbide slips provide greater holding ability and improved wear resistance in high-strength casing. Pressure through the tubing activates the slips in the hydraulic holddown mechanism.

•  An optional integral circulating valve locks into open or

closed position during squeezing or treating operations,

and opens easily to allow circulation above the packer.

Operation

The tool is run slightly below the desired setting position to set the packer and is then picked up and rotated several turns. If the tool is on the bottom, only a half-turn is actually required. However, in deep or deviated holes, several turns with the rotary may be necessary. To maintain position, theright-hand torque must be held until the mechanical slips on the tool are set and can start taking weight.The pressure must be equalized across the packer to unset it.

As the tubing is picked up, the circulating valve remains closed, establishing reverse circulation around the lower end of the packer. The circulating valve is opened for coming out of the hole when the tubing is lowered, rotated to the right, and picked up.

RTTS Packer

Casing Size (in) OD in.(cm) ID in.(cm) Thread connnections Length in.(cm) Tensile Rating** lb (kg)  
7 5/8 20-39   6.35 (16.13) 2.40 (6.10) 4 5/32 in. 8 UNS 3 7/8 in. CAS
9 5/8 40-71.8 7.80 (19.81) 3.00 (7.62)  4 1/2 in. API IF T.J.  4 1/2 in. API IF T.J
29.3-53.5 8.15 (20.70) 3.75 (9.53) 4 1/2 in. API IF T.J. 4 1/2 in. API IF T.J.

Nhóm Marketing

Quản lý online

Liên kết nội bộ

Giá dầu